next »

[cryogenic]

@flash78 - I installed my infectus the opposite way round, all wires are really short that way. Not had any issues so far (might be worth trying)

[3lix0r]

I said I converted my 14 wire alternate install into the 9 wire install using the same conversion posted by krayziexploiter

Sorry TD I missed your first post that stated that.
Thanks again, I have used the alternate install.

I'm running into an issue hopefully someone can help.

I finished my install and I placed in a game and it took over 30 seconds to initialize the drive. After it failed to read the disc (original and backup). I went back and shortened the U wire and now the drive initializes like it normally would, however, I still get a disc read error (original and backup).

Some background information:
I had all wires but except P, Q, T, GND, & 5v and all original games worked.
When I soldered P, Q, T, GND, & 5v is when I got the read error.

I read over the threads and I didn't see anyone with these issues.
Any ideas?
Is it my installation, any idea where I can check?

Also, this is a USA wii D2C

Thanks,
lix

[dexter955]

I repeat the same thing always:

1 - Wii off
2 - Insert Disc for  init Wii
3 - Many times wii boot witout any problem
3 - Some times delayed 10 - 45 sec to init dvd drive
3 - Rarely dvd drive don't init and dont take dvd disc
4 - Switch Off Wii (don't have wiiconnect).

I have the same problem (I used the new U point).  There are a lot of problems with the insertion/ejection of the disk because while inserting or ejecting a disk it seems that the infectus goes out of sync (blu led OFF).

[Psycho007]

When can we expect diagram and firmware for ARGON 

[Td]

I said I converted my 14 wire alternate install into the 9 wire install using the same conversion posted by krayziexploiter

Sorry TD I missed your first post that stated that.
Thanks again, I have used the alternate install.

I'm running into an issue hopefully someone can help.

I finished my install and I placed in a game and it took over 30 seconds to initialize the drive. After it failed to read the disc (original and backup). I went back and shortened the U wire and now the drive initializes like it normally would, however, I still get a disc read error (original and backup).

Some background information:
I had all wires but except P, Q, T, GND, & 5v and all original games worked.
When I soldered P, Q, T, GND, & 5v is when I got the read error.

I read over the threads and I didn't see anyone with these issues.
Any ideas?
Is it my installation, any idea where I can check?

Also, this is a USA wii D2C

Thanks,
lix

You didn't say whether or not you soldered the Region-patching wires. You need to solder I and G to ground.

[3lix0r]

I said I converted my 14 wire alternate install into the 9 wire install using the same conversion posted by krayziexploiter

Sorry TD I missed your first post that stated that.
Thanks again, I have used the alternate install.

I'm running into an issue hopefully someone can help.

I finished my install and I placed in a game and it took over 30 seconds to initialize the drive. After it failed to read the disc (original and backup). I went back and shortened the U wire and now the drive initializes like it normally would, however, I still get a disc read error (original and backup).

Some background information:
I had all wires but except P, Q, T, GND, & 5v and all original games worked.
When I soldered P, Q, T, GND, & 5v is when I got the read error.

I read over the threads and I didn't see anyone with these issues.
Any ideas?
Is it my installation, any idea where I can check?

Also, this is a USA wii D2C

Thanks,
lix

You didn't say whether or not you soldered the Region-patching wires. You need to solder I and G to ground.

Sorry TD, I have an infectus 2.
I don't need to do that for v2 right, that's only for v1?

Thanks

[Td]

My mistake. I must've missed that in your posts.

You need to leave the programmer connected and flip switch 1 AND 2 both to the ON position for a USA Wii.

[3lix0r]

My mistake. I must've missed that in your posts.

You need to leave the programmer connected and flip switch 1 AND 2 both to the ON position for a USA Wii.

I programmed the infectus2 before I soldered it in, with the USA configuration.
Would I still need to connect it?

Thanks again

[Td]

Yes. I believe the programmer needs to be connected at all times. Maybe I'm wrong, but it's worth a shot.

Maybe Infectus can also say whether or not the I/G wires work for the Infectus2. That seems like an easier way to configure it than using the programmer.

[3lix0r]

Yes. I believe the programmer needs to be connected at all times. Maybe I'm wrong, but it's worth a shot.

Maybe Infectus can also say whether or not the I/G wires work for the Infectus2. That seems like an easier way to configure it than using the programmer.

Hey Td,

Thanks for all the help. I thought the programmer was needed only to program, however it is needed for the chip to work.
Once I attached it everything started working. Thanks again!!

Infectus way to go!

Cheers,
lix

[krayziexploiter]

I'm pretty sure the I/G ground bridges should also work on infectus2. The code is exactly the same.

[Psycho007]

 
Infectus2 / wasabus

Have one Wii were it wont work.

Serial: LEH1641XXXX
D2C / D1A

Original wont boot
Backup wont boot
All seams works as it should work but after 2-3 sec. after spinning up disk the drive stops.

Have try 2 pcs. Infectus2 same results, i made complete new install.
the first mod i install, is now in other Wii and works. LEH17XXXXX D2C / D1A


Both Wii was out off the box (NEW)

Maby Wasabus don't work in all wii 
this is the first out off 20 Wii it wont work, ill try now to make Wiiktus install and See how it goes.

[theforce81]

Infectus2 / wasabus

Have one Wii were it wont work.

Serial: LEH1641XXXX
D2C / D1A

Original wont boot
Backup wont boot
All seams works as it should work but after 2-3 sec. after spinning up disk the drive stops.

Have try 2 pcs. Infectus2 same results, i made complete new install.
the first mod i install, is now in other Wii and works. LEH17XXXXX D2C / D1A


Both Wii was out off the box (NEW)

Maby Wasabus don't work in all wii 
this is the first out off 20 Wii it wont work, ill try now to make Wiiktus install and See how it goes.

Hey there,

This is a common problem with the Wasabi as well, so the Wiiktus will work. Good luck on it.

[zchaw]

Anyone know the ohm reading for the resistor at point U, mine fell off.

[Psycho007]

Hey there,

This is a common problem with the Wasabi as well, so the Wiiktus will work. Good luck on it.

Wiiktus works 

But now i have had 5 wii out of 36 wii were Wasabus dont work.
3 pcs. LEH16 and 1 pc. LEH17 and 1 pc. LEH14 all D2C/D1A